Getting Started with Plumber's Essentials When Installing a Bathtub
Getting Started with Plumber's Essentials When Installing a Bathtub
Blog Article
The writer is making a few good pointers on the subject of A Step-by-Step Guide to Installing a Bathtub as a whole in this article in the next paragraphs.
Mounting a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately challenging task. If the old bathtub is conveniently available, the job can relocate speedily; if you need to open a wall to get rid of the old tub and place the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the new one. See to it you have certified on your own for the work and fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed task, it is much better to take into consideration employing one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This write-up will aid you mount a brand-new bath tub in your shower room if you have actually already bought a brand-new tub and don't require to transform the setup of your previous water supply pipelines.
Your devices as well as material checklist need to make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water supply. After doing so, turn on the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipes. Once the supply pipelines have been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this process. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Protect the tap in place with the supplier offered backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet ports. The former type ought to be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Using both wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bath tub up until the spirit level reads degree.
To set up faucets, fit the bottom of the outermost flexible tap port to the suitable supply pipe by making a compression join; then do the exact same for the other faucet.
Activate the water supply and also inspect all joints and new pipework for leaks and tighten them if required. Load the tub and additionally check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bath paneling as described in the supplier's user's manual. Tiling as well as securing around the tub needs to wait till the bath tub has been utilized at least when as this will certainly resolve it into its last setting.
Planning for the Installment
First of all, the sustaining framework supplied with the bath should be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to prevent stress on the bath tub.
Fit the flexible tap ports to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to crack a stiff seal, causing the water to penetrate the wall surface between the bath and also the tiling, leading to complications with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to always load the tub with water before securing, to permit the movement experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently offered on the market. It is recommended to fit the floor tiles making use of waterproof or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that article about Tools You Need to Install a New Bathtub through an acquaintance on our other website. Don't hesitate to take a moment to distribute this blog post if you enjoyed it. I am grateful for your time. Come back soon.
Emergency? Call us! Report this page